無料 NEC 314.16 ボックス充填計算ツール

ボックス容量計算ツール 電気工事士のために

NEC 314.16に基づく無料の電気ボックス充填計算ツールです。導体、器具、クランプ、接地導体、支持金具、端子台ごとの必要容積を明細で確認でき、ボックスの充填量を計算して施工が規定に適合しているか確認できます。

ボックス容量計算

Calculate electrical box fill requirements per NEC 314.16

Your box & components
01 Choose your box
Box capacity— in³
02Count what’s insideWire gauge
Same wire gauge throughout, including grounds
2.25 in³ per allowance
Exclude grounds
Count mounting straps
Entering the box
Inside the box only
Updates as you edit. Grounds are counted separately.

Box Fill Calculator

当ボックス充填計算ツールの特長

NEC 314.16に基づく容積計算を部品ごとにすべて表示する無料のボックス充填計算ツールです。結果を検算し、配置計画や検査、手直しの際に計算の根拠を説明できます。

NEC 2023対応

314.16(B)(6)の端子台規定を含む最新の国家電気規程に対応しています。

瞬時に結果表示

数秒で正確なボックス充填計算結果を取得。各部品の容量内訳も詳細に表示します。

完全無料

会員登録不要。必要な時にいつでも正確な計算ができるボックス充填計算ツールです。

モバイル対応

どのデバイスでもボックス充填を計算可能。現場での計算に最適です。

ボックス充填計算ツールの使い方

NEC 314.16に基づくボックス充填計算を3つのステップで

  1. 01

    ボックスタイプを選択

    標準的な電気ボックスサイズから選択するか、カスタム寸法を入力して充填計算を行います。

  2. 02

    部品を追加

    導体、デバイス、クランプ、接地線を入力し、正確なボックス充填量を計算します。

  3. 03

    結果を確認

    電気ボックスがNEC 314.16の充填要件を満たしているか即座に確認できます。

How to Calculate Box Fill by Hand

This worked example uses the calculator's demo setup: a 4" x 2-1/8" square box (30.30 in³) with six 12 AWG conductors, one device yoke, three entering equipment grounding conductors (EGCs) and internal cable clamps. Every allowance uses the 12 AWG volume of 2.25 in³ from Table 314.16(B).

  1. 314.16(B)(1) Conductors: 6 conductors × 2.25 in³ = 13.50 in³. Each insulated conductor that comes from outside the box and is spliced or terminated inside counts once.
  2. 314.16(B)(2) Internal cable clamps: one or more clamps count as a single allowance, 1 × 2.25 in³ = 2.25 in³.
  3. 314.16(B)(3) Support fittings (fixture studs, hickeys): none in this box, 0.00 in³. Each type present would add one allowance.
  4. 314.16(B)(4) Device yokes: one yoke counts as two allowances, 2 × 2.25 in³ = 4.50 in³.
  5. 314.16(B)(5) Equipment grounding conductors: 1 to 4 entering EGCs share one allowance, and each EGC beyond four adds one-quarter allowance. Three EGCs = 1 × 2.25 in³ = 2.25 in³ (six EGCs would be 1.5 allowances).
  6. 314.16(B)(6) Terminal blocks: none in this box, 0.00 in³.

Required volume: 13.50 + 2.25 + 0.00 + 4.50 + 2.25 + 0.00 = 22.50 in³. The box holds 30.30 in³, so the calculated fill uses 74.3% and leaves 7.80 in³. This checks box volume only; confirm the volume marked on your box and verify other installation requirements separately.

Open this example in the calculator

Box Fill Volume Allowance by Wire Size

Each counted allowance uses the volume for the conductor size in this table. Where a rule says to use the largest conductor, use that size.

Wire size (AWG)Volume per allowance (in³)Volume per allowance (cm³)
18 AWG1.5024.6
16 AWG1.7528.7
14 AWG2.0032.8
12 AWG2.2536.9
10 AWG2.5041.0
8 AWG3.0049.2
6 AWG5.0081.9

Source: NEC 2023 Table 314.16(B). Checked 2026-11-21.

ボックス充填計算 よくある質問

電気ボックスの充填計算とは?

ボックス充填計算は、NEC第314.16条に基づき、電気ボックスにすべての導体、デバイス、付属品を収容するのに十分な容量があるかを判定するものです。この計算ツールにより安全な施工と過熱防止を確保します。

ワイヤーナットはボックス充填計算に含まれますか?

含まれません。ワイヤーナット(ツイストオンコネクタ)はボックス充填に算入しません。NEC 314.16に基づき、導体、デバイス、クランプ、接地導体のみを計算します。

接地線はボックス充填計算でどのように数えますか?

ボックス内のすべての機器接地導体は、NEC 314.16(B)(5)に基づき、ボックスに入る最大の機器接地導体のサイズで単一導体容量として計算されます。

接地線はボックス充填計算でどのように数えますか? (English page)

NEC 2023でボックス充填に関して何が変わりましたか?

NEC 2023では314.16(B)(6)が追加され、端子台をボックス充填計算に含めることが必要になりました。本ツールはNEC 2023に完全対応し、接続された最大導体に基づいて端子台を計算します。

ボックス充填を計算しませんか?

無料のボックス充填計算ツールで、電気施工がNEC 314.16の要件を満たしているか確認しましょう。2023年版の314.16(B)(6)に規定された端子台の必要容積にも対応しています。

ボックス充填計算を開始