도체 디레이팅 및 박스 필 가이드

전선관 채움, 묶음 도체, 주변 온도 또는 전압강하로 전선 크기가 바뀌어도 박스는 NEC 314.16을 통과해야 합니다.

디레이팅과 박스 필이 혼동되는 이유

Conductor derating is the process of reducing or adjusting conductor ampacity when conditions such as more current-carrying conductors, higher ambient temperature, rooftop raceways, or insulation temperature limits change how much current the conductor can safely carry.

Box fill is the NEC 314.16 enclosure-volume calculation. It does not ask whether the conductor ampacity is high enough; it asks whether the box has enough marked cubic inches for insulated conductors, grounding conductors, device yokes, internal clamps, and fittings.

The two checks meet in the field when a designer upsizes wire. A circuit that was selected as 12 AWG for ampacity may become 10 AWG for derating or voltage drop. The conductor count may stay the same, but the box-fill allowance increases immediately.

분리해야 할 정의

Conductor derating is an ampacity correction or adjustment workflow used to keep conductors within safe thermal limits under NEC 310.15 and related tables.

Box fill is an enclosure-volume calculation under NEC 314.16 that assigns cubic inches to countable conductors, device yokes, internal clamps, support fittings, and equipment grounding conductors.

Ampacity is the maximum current a conductor can carry continuously under stated conditions without exceeding its temperature rating. It is not the same thing as the physical volume that conductor occupies in a box.

박스 선택 전 다섯 가지 현장 규칙

Finish the ampacity check first

Apply NEC 310.15 adjustment and correction factors before locking the conductor size. If derating pushes 12 AWG to 10 AWG, the box-fill value changes.

Recalculate box fill after every wire-size change

NEC Table 314.16(B) uses 2.25 cu.in. for 12 AWG, 2.50 cu.in. for 10 AWG, 3.00 cu.in. for 8 AWG, and 5.00 cu.in. for 6 AWG.

Count conductors, not circuits

A multiwire branch circuit, control bundle, or solar homerun may look like one design item, but each eligible conductor entering the box must be counted.

Do not let conduit fill hide a box problem

A raceway can pass its own fill and ampacity checks while the destination box fails because of yokes, clamps, grounding allowances, or larger conductors.

Use IEC logic as a workflow, not a table swap

IEC 60364 projects use different national calculations, but conductor temperature, grouping, bend radius, terminal access, and enclosure space still need separate review.

디레이팅 결정과 박스 필 결과

디레이팅, 전압강하 또는 온도로 전선 크기가 바뀌면 같은 도체 수라도 다른 함체가 필요할 수 있습니다.

Scenario	Derating or ampacity check	Box-fill count	Required volume	Field decision
20 A receptacle feed-through with line, load, GFCI yoke, grounds, and internal clamp	12 AWG remains acceptable after adjustment	8 allowances at 12 AWG	8 x 2.25 = 18.00 cu.in.	Use a deep 1-gang or 4 in. square box instead of a shallow device box.
Same GFCI layout upsized to 10 AWG for derating or voltage drop	10 AWG selected after NEC 310.15 review	8 allowances at 10 AWG	8 x 2.50 = 20.00 cu.in.	The wire-size change adds 2.00 cu.in.; an exact-limit 18 cu.in. box now fails.
Multiwire branch circuit in a kitchen 2-gang box with two yokes and shared neutral	Current-carrying conductor count may affect ampacity in the raceway	10 allowances at 12 AWG	10 x 2.25 = 22.50 cu.in.	Verify handle-tie and neutral rules separately, then choose a deep 2-gang box.
Rooftop or hot attic junction where 10 AWG conductors replace 12 AWG	Ambient correction or rooftop conditions drive upsizing	6 allowances at 10 AWG	6 x 2.50 = 15.00 cu.in.	A 16 cu.in. box passes on paper but leaves little service margin in a hot space.
Small equipment transition upsized to 8 AWG conductors	Ampacity or voltage drop requires 8 AWG	6 allowances at 8 AWG	6 x 3.00 = 18.00 cu.in.	Choose a larger enclosure because 8 AWG stiffness matters beyond the legal cubic inches.
IEC control enclosure changed from 2.5 mm2 to 6 mm2 conductors	Grouping, temperature, and national IEC rules change conductor cross-section	NEC cubic-inch table does not apply directly	Check local enclosure-space and bend-radius rules	Keep ampacity, terminal room, and enclosure volume as three separate decisions.

구체적인 수치 예

Example 1: 12 AWG GFCI feed-through that passes at 18.00 cu.in.

A line/load GFCI box has four insulated 12 AWG conductors, one equipment-grounding allowance, one internal clamp allowance, and one device yoke that counts as two allowances. The total is 8 allowances. NEC Table 314.16(B) assigns 2.25 cu.in. to 12 AWG, so the required volume is 18.00 cu.in. This is a box-fill result, not an ampacity result.

Example 2: the same layout upsized to 10 AWG

If conductor derating, voltage drop, or equipment instructions push the same layout to 10 AWG, the count remains 8 allowances but the allowance changes to 2.50 cu.in. The required volume becomes 20.00 cu.in. The installer did not add a device or another cable, yet the old 18 cu.in. box no longer passes.

Example 3: 8 AWG equipment transition

A transition box with four insulated 8 AWG conductors, one equipment-grounding allowance, and one internal clamp allowance has 6 allowances. At 3.00 cu.in. per 8 AWG allowance, the NEC 314.16 minimum is 18.00 cu.in. Because 8 AWG conductors are stiff, many electricians move to a 30.3 cu.in. or larger enclosure for workable bends and future service.

확인할 코드 참조

용어는 공개 자료로 확인하고 최종 설치는 채택 코드, 절연 정격, 장비 인증, 현지 요구사항으로 검증하십시오.

National Electrical Code: Use NEC 310.15 for ampacity adjustment and correction, and NEC 314.16 for box-fill volume.
American wire gauge: Helpful for comparing why 12 AWG, 10 AWG, 8 AWG, and 6 AWG use different volume allowances.
Ampacity: Background for conductor current-carrying capacity, temperature limits, and derating logic.
IEC 60364: International users should apply local IEC-based rules while keeping ampacity and enclosure-space checks separate.

도체 디레이팅 및 박스 필 FAQ

Does conductor derating change the box-fill conductor count?

Usually no. Derating may change the conductor size, while NEC 314.16 conductor count still depends on how many eligible conductors, yokes, clamps, fittings, and grounding allowances are in the box.

Why can the same box fail after wire upsizing?

Because the cubic-inch allowance increases with wire size. Eight allowances at 12 AWG require 18.00 cu.in.; eight allowances at 10 AWG require 20.00 cu.in.

Which NEC sections should I check together?

Use NEC 310.15 for ampacity adjustment and correction, NEC 314.16 for box fill, NEC Chapter 9 and 300.17 for raceway fill context, and NEC 110.3(B) for listed equipment instructions.

Does a larger raceway solve a crowded box?

No. A larger raceway can help conductor fill and pulling, but the destination box still needs enough marked volume for the conductors and devices under NEC 314.16.

How do grounding conductors count after derating?

All equipment grounding conductors together still count as one allowance under NEC 314.16(B)(5), based on the largest equipment grounding conductor present.

How should IEC users apply this guide?

Use it as a workflow: check grouping and temperature for conductor sizing, then separately check terminal room, bend radius, heat, and enclosure access under the local IEC-based rules.

기술 메모

Hommer Zhao reviews these guides from a conductor-packaging and termination-access perspective. The goal is to help electricians, engineers, and DIYers separate code arithmetic from physical workmanship before the box is installed.

도체 크기가 바뀔 때마다 박스 재확인

허용전류와 디레이팅 판단 후 최종 전선 크기, 수량, 요크, 접지, 클램프를 계산기에 입력하십시오.